🎯 Trouvez le bon produit de ventilation
Demandez à notre IA CVC — obtenez des spécifications et une recommandation en quelques secondes
🔍
HT-DG60A1 Industrial Dehumidifier product image

HT-DG60A1 Industrial Dehumidifier | 60 L/D Moisture Control

Confirm by exact model datasheet industrial dehumidifier for moisture-control projects

CONTRÔLE DE L'HUMIDITÉ
Confirm by exact model datasheet industrial dehumidifier for moisture-control projects
VÉRIFICATION DE L'ALIMENTATION
AC220V-50Hz; confirm exact circuit before ordering
Confirmer la charge de la pièce, l'humidité cible et le plan de drainage avant devis
Ajouter au devis
Contrôle industriel de l'humidité
Déshumidificateur industriel HT-DG240A1 | Contrôle de l'humidité à haute capacité 240 L/j

HT-DG60A1 Industrial Dehumidifier | Compact Moisture Control

HT-DG60A1 is an industrial dehumidifier option for warehouses, production rooms, storage areas and equipment spaces where moisture control affects comfort, corrosion risk, product storage or process stability.

Capacity60 L/D
PowerAC220V-50Hz / 680 W
Selection factors: Size this unit on the moisture the room actually gains, not on floor area alone. At 60 L/D and 680 W it suits a single storage room, utility area or small workshop on a 220 V supply.
Placement check: keep air inlet and outlet paths clear, plan drainage where needed, and avoid positions where condensate or dust can block airflow.

Selection flow

Project flow

1Humidity loadestimate litres per day for the room, not just its area.
2Drainagedecide between tank use and a gravity or pump drain for long runs.
3Air circulationkeep inlet and outlet clear and leave room for maintenance.
4Project detailsSend quantity, destination and the documents your project needs.

Application fit

Where this model fits, and what to verify first

Best fitSmall storage rooms, utility areas and single-room moisture control where the load is light and the supply is 220 V.
Check firstActual moisture load, room volume, and whether 60 L/D leaves enough margin for door openings.
AvoidSpecifying it for a large warehouse or a wet process room. At 60 L/D it is a compact unit, not a whole-hall solution.
Buyer noteOne of the smallest models in the series. Confirm the daily moisture load first, because a compact unit with no margin will run continuously.

Source-backed Technical Parameters

Source-backed rows only: no missing/PDF-absent models are added. Medium-confidence rows keep confirmation notes.
HT-DG60A1 Industrial Dehumidifier | 60 L/D Moisture Control technical and selection table
Source model PIM/page model Dehumidification Voltage Input power Airflow Size Confidence
HT-DG60A1 LG-DG60A1 60 L/D AC220V-50Hz 680 W Confirm by exact model datasheet 380x420x635 medium

Source notes:
HT-DG60A1 → LG-DG60A1: medium confidence, source page 73; Page heading HT-DG60A1; OCR product model reads DG60AG. Mapped to existing LG-DG60A1 variant with source-model mismatch.

Legacy page note: Original page content was backed up before this source-backed UI v4 update.

Best-fit Applications

This model is built for rooms that gain moisture slowly: a storeroom, a small packing area or a utility space where damp air would otherwise reach stored goods. At 60 L/D it is not intended for a wet production line, but it removes ambient moisture well when the load is modest.

Because it runs on a standard 220 V single-phase supply at 680 W, it can be placed where no three-phase power is available. Check the drain route before you commit, since even a small unit produces a steady trickle when it runs for long periods.

  • Small stores: keeps cartons, packaging and spare parts dry in a compact room.
  • Utility areas: reduces damp air around equipment and stored tools.
  • Backup drying: supports spot drying after a leak where the affected area is small.

Selection guide

  • Moisture load: estimate litres per day for the room, not just its area.
  • Drain route: decide between tank use and a gravity or pump drain for long runs.
  • Supply: single-phase 220 V is enough; check the circuit can carry 680 W.
  • Placement: keep inlet and outlet clear and leave room for maintenance.
  • Temperature: moisture removal falls in cold rooms, so check the working range.

What NOT to Buy

HT-DG60A1 Industrial Dehumidifier | 60 L/D Moisture Control technical and selection table
Situation Risk Better action
Area only is known The 60 L/D capacity may be far too small for the load. Work out litres per day before choosing this model.
Large warehouse expected A compact unit will run non-stop and still miss the target. Step up to the HT-DG240A1 or larger.
No drain planned The tank fills quickly during continuous running. Plan a drain before installation.
Cold room under 15 °C Capacity drops and defrost cycles shorten running time. Confirm the working range for a cold store.

Industrial Dehumidifier Buyer Checklist

Use the source-backed product information on this page as the starting point, then confirm site conditions before approving the final model.

  • Daily moisture load in litres for the room
  • Room volume and how often doors open
  • Drain method: tank, gravity drain or pump
  • 220 V circuit capacity and placement clearance
Selection note

HT-DG60A1 is positioned for compact moisture control; confirm capacity, drainage and site humidity load before final selection.

Core Engineering Features

HT-DG60A1 Industrial Dehumidifier | Compact Moisture Control set against the published values on this page. Every point below is taken from this model’s own data.

Capacity60 L/D
PowerAC220V-50Hz / 680 W
PIM/page modelLG-DG60A1
Dehumidification60 L/D
VoltageAC220V-50Hz
Input power680 W

Quality Assurance & Warranty

Dehumidifier orders are verified at the factory before shipping, because a unit sized for a humidity target is only useful if it arrives working to that target.

Applied to this model: Capacity 60 L/D, Power AC220V-50Hz / 680 W. These checks are run against that specification before the unit ships.

Unit-level humidity checkChecks cover compressor start, coil and drain integrity, airflow, humidity sensor response and model-to-table parameter matching.
Documented complianceCE LVD/EMC and RoHS files cover the listed HT, LG and HT-DG dehumidifier families; see the documents section below.
Warranty supportWarranty for dehumidifier orders is confirmed with the quotation for your destination market.
Service parts for dehumidifiersFilters, drain fittings, humidity controllers and common service items.

OEM/ODM & Supply Options

For distributors and contractors working on moisture-control projects, the supply side adapts to your market instead of one fixed cabinet build.

For this model (Capacity 60 L/D, Power AC220V-50Hz / 680 W), the OEM route can start from that base specification rather than a blank sheet.

OEM/ODMBadging, packaging and control options for dehumidifier orders, including branded cartons and manual inserts.
Capacity and duty-point adjustmentHumidity control range, capacity class and drainage arrangement can be reviewed against your project.
Voltage & plug optionsVoltage and plug configuration for this product line can be reviewed during quotation.
Documentation & bulk supplyCatalogues, technical sheets, available certificates, volume pricing and distributor programs for this product line.
Order quantity & lead timeMinimum order quantity, sampling and production lead time are confirmed per model and order volume — see the B2B supply page for how sourcing enquiries are handled.

Documents & conformité

This dehumidifier series is supported by Linggong Electric CE LVD/EMC and RoHS documentation for the listed HT, LG, HT-DG, LG-DG and LG-D dehumidifier model ranges.

  • CE AttestationM.2025.206.C118876
  • Technical FilesDTCF0509-LVD/EMC and DTCF0509-ROHS
  • ApplicantZhejiang Linggong Electric Appliance Co., Ltd.

Scope boundary: use these documents for the dehumidifier model families listed in the certificates. The DTS1250 SGS performance report is not used here because its applicant/model scope does not match Linggongshare pages.

FAQ

How do I choose dehumidifier capacity?

Work out the daily moisture the room gains in litres, then check that 60 L/D covers it with margin. For a small store or utility room the load is often modest, but a wet process area can exceed 60 L/D quickly, so measure before you buy.

Can it run continuously?

Yes, but it needs a drain plan. At 680 W it runs continuously on a 220 V supply as long as condensate is removed by tank, gravity drain or pump. In a small room, check that it is not simply running non-stop because the load is too high for 60 L/D. Keep the inlet and outlet clear, wash the filter on the schedule in the manual, and keep the drain flowing. In a dusty small room, the filter needs attention more often than the manual suggests.

Why do some model names differ?

Some source rows use HT model codes while the website/PIM layer may use LG model codes. Both are shown to avoid silent normalization.

Download product catalog PDF

Download the English industrial dehumidifier catalog for product-family overview and technical review. Confirm the exact HT model, voltage and installation conditions with our team before relying on it for project selection.

Download catalog PDF

Use the exact model, voltage and installation conditions for project selection.

Product inquiry

Confirm the published specifications, then add this product to your quote list.

Contact sales