🎯 Das passende Lüftungsprodukt finden
Fragen Sie unsere HLK-KI — erhalten Sie Spezifikationen & Empfehlung in Sekunden
🔍
HF-200 oblique-flow pressurized inline duct fan product image
Illustrative ceiling-hung HF-200 inline duct installation with round duct connections
HF-200 overall dimensions: 303 mm length, 245 mm height and 245 mm width
  1. HF-200 oblique-flow pressurized inline duct fan product image
  2. Illustrative ceiling-hung HF-200 inline duct installation with round duct connections
  3. HF-200 overall dimensions: 303 mm length, 245 mm height and 245 mm width

HF-200 / HF-315 Oblique-Flow Pressurized Duct Fan | Dual-Model Inline Fan

HF-200 and HF-315 share the same oblique-flow housing form at different performance classes. Compare airflow, static pressure, duct route and power before requesting a quote.

Shared housing reference visual: confirm the selected model in the comparison table below.

PROJEKTEIGNUNG
Inline duct boosting where airflow and static-pressure requirements must be confirmed.
LEISTUNGSBEREICH
HF-200: 700–900 m³/h · HF-315: 2900 m³/h
MODEL RANGE
HF-200 / HF-315
Zum Angebot hinzufügen

SHARED HOUSING · TWO PERFORMANCE CLASSES

Choose HF-200 or HF-315 for the Project Duty

HF-200 and HF-315 share the same oblique-flow housing form. Select HF-200 for the published 700–900 m³/h operating range, or HF-315 for a 2900 m³/h high-airflow project. Confirm duct route, static pressure and power before final approval.

The gallery is a shared housing reference. The HF-200 dimensional drawing remains HF-200-specific; request HF-315 drawing confirmation for the selected project.

Compare the two models

MODEL DECISION

Start with Required Airflow and Project Conditions

HF-200

Medium duct boosting

Published airflow
700–900 m³/h
Published static pressure
302–380 Pa
Speed mode
Single-speed or dual-speed

Choose when the published operating row and 200 mm duct route match the project duty.

HF-315

High-airflow duct project

Published airflow
2900 m³/h
Published static pressure
630 Pa
Speed mode
Single-speed

Choose when the larger airflow duty, duct route and power supply are confirmed for the project.

Published HF-200 and HF-315 comparison
Modell Speed mode Published airflow Published static pressure Voltage Confirm before quote
HF-200 Single-speed or dual-speed 900 m³/h; 900 / 700 m³/h dual-speed 380 Pa; 380 / 302 Pa dual-speed 220 V / 50 Hz Duct fit, operating row and route resistance.
HF-315 Single-speed 2900 m³/h 630 Pa 220 V / 50 Hz Duct route, project duty and power supply.

Two different HF duct-fan lines share this prefix

The published catalogue documents two distinct families, and both use model names starting with “HF”:

Model names appearing in both lines carry different published airflow, static pressure and noise figures. Confirm which line your project specifies, and the matching datasheet, before ordering.

PROJECT CHECK

Do Not Select by Duct Diameter Alone

Use the selected model’s published operating row together with airflow demand, static pressure, duct diameter and route, voltage / frequency, quantity and destination market.

Shared installation boundary

Confirm available installation space, duct joints and maintenance access. The gallery installation image is illustrative, not a project-specific installation drawing.

DOCUMENTS AND SCOPE

Confirm Model and Market Scope Before Procurement

HF-200

The HF-200 drawing shown in the gallery is specific to HF-200: 303 × 245 × 245 mm.

HF-315

Request dimensional drawing and document-scope confirmation with the selected model and project requirement.

Compliance

No model-specific certificate is listed for HF-200 / HF-315 in the compliance center. Confirm applicable documents before procurement.

Open compliance scope

FAQ

Selection Questions

Is HF-315 a larger performance version of HF-200?

They share the same oblique-flow housing form, but selection must use each model’s published airflow, static pressure, speed mode and project conditions.

Can I select only by duct diameter?

No. Confirm airflow, static pressure, duct route and selected operating row before final approval.

What information is needed for a quote?

Send the selected model, airflow, duct route and diameter, static-pressure requirement, voltage / frequency, quantity and destination market.

Zentrale Konstruktionsmerkmale

Choose HF-200 or HF-315 for the Project Duty set against the published values on this page. Every point below is taken from this model’s own data.

Speed modeHF-200: single-speed or dual-speed · HF-315: single-speed
Published airflowHF-200: 900 m³/h (900 / 700 m³/h dual-speed) · HF-315: 2900 m³/h
Published static pressureHF-200: 380 Pa (380 / 302 Pa dual-speed) · HF-315: 630 Pa
Voltage220 V / 50 Hz for both models

Qualitätssicherung & Garantie

Ventilatorbestellungen werden vor dem Versand im Werk geprüft, denn veröffentlichter Luftstrom und Druck gelten nur, wenn das gelieferte Gerät seiner Tabellenzeile entspricht.

Applied to this model: 900 m³/h at 380 Pa single-speed, or dual-speed 900 / 700 m³/h at 380 / 302 Pa. These checks are run against that specification before the unit ships.

Prüfung von Luftstrom und DruckDie Prüfungen umfassen Motoranlauf, Laufradauswuchtung, Luftstrom- und statische Druckprüfung, Lärmbewertung und Abgleich der Parameter Modell zu Tabelle.
Documented complianceCE-, RoHS- und zugehörige Dateien decken die aufgeführten Ventilatorfamilien ab; siehe den Dokumentenbereich unten.
Warranty supportDie Garantie für Ventilatorbestellungen wird mit dem Angebot für Ihren Zielmarkt bestätigt.
Service parts for fansLaufräder, Motorkondensatoren, Montagewinkel und gängige Verschleißteile.

OEM/ODM & Supply Options

Für Distributoren und Auftragnehmer in Lüftungsprojekten passt sich die Lieferseite Ihrem Markt an statt einer festen Ventilatorkonstruktion.

For this model (900 m³/h at 380 Pa single-speed, or dual-speed 900 / 700 m³/h at 380 / 302 Pa), the OEM route can start from that base specification rather than a blank sheet.

OEM/ODMBadging-, Verpackungs- und Steuerungsoptionen für Ventilatorbestellungen, einschließlich gebrandeter Kartons und Handbuchbeilagen.
Luftstrom- und DruckvariantenModellauswahl, Motorleistung und Spannungsoptionen werden gegen Ihre Kanalberechnung geprüft.
Voltage & plug optionsSpannung und Steckerkonfiguration für diese Produktlinie können im Angebot geprüft werden.
Dokumentation & GroßhandelsversorgungKataloge, technische Datenblätter, verfügbare Zertifikate, Mengenpreise und Händlerprogramme für diese Produktlinie.
Bestellmenge & VorlaufzeitMindestbestellmenge, Musterstellung und Produktionsvorlaufzeit werden je Modell und Bestellvolumen bestätigt — siehe die B2B supply page zur Bearbeitung von Beschaffungsanfragen.

Dokumente & Compliance

Download the HF-200 / HF-315 pressurized duct fan datasheet (PDF) used for the technical values on this page.

Bestätigen Sie das genaue Modell und die aktuelle Dokumentation vor Angebot oder Projektdokumentation.

Alle Zertifizierungen und Compliance-Dokumente nach Produktumfang ansehen

Typical Project Applications

The HF-200 and HF-315 are intended for inline duct-boosting projects where the airflow, static pressure, duct route and electrical supply are known before model confirmation.

  • Fresh-air or exhaust duct routes that need a defined inline fan duty point.
  • Medium-airflow duct boosting where the published HF-200 operating row matches the project requirement.
  • Higher-airflow duct projects where the published HF-315 duty, route resistance and power supply are suitable.
  • Ceiling or service-area installations where duct joints, maintenance access and the selected model drawing must be checked together.

When this page is not enough for final selection

Do not select between HF-200 and HF-315 from duct diameter alone. If the project has a specific noise limit, unusual duct resistance, a special control requirement, a market-specific document scope or a non-standard installation, send those conditions for technical review before procurement.

PROJECT INQUIRY

Request a Quote for the Selected Model

Choose HF-200 or HF-315 above to retain the right model context.